Exactly How to Remove and Change a Tub.
Exactly How to Remove and Change a Tub.
Blog Article
This post listed below on the subject of A Step-by-Step Guide to Installing a Bathtub is relatively entertaining. Read it for yourself and see what you think of it.
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, and also sometimes, tiling skills. Changing an old bath tub with a new one is also a reasonably hard project. If the old tub is easily obtainable, the project can move immediately; if you need to open a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to move out the old tub as well as set in the brand-new one. See to it you have actually qualified yourself for the task as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is far better to take into consideration employing one before you begin. Chances are you may need an expert plumber to make tube links.
This post will certainly aid you mount a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not require to transform the setup of your previous water supply pipelines.
Your devices and also product list need to consist of the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be rather problematic due to the limited accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel prepared for the staying water that will come from the pipelines. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Before going on to fit the new taps, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin making sure that the washers remain in place in between the tap as well as the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The previous type must be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using both wood boards under its feet, place the tub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four little factors.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bathtub until the level reviews level.
To set up faucets, fit all-time low of the furthest flexible tap port to the ideal supply pipe by making a compression join; then do the very same for the various other tap.
Turn on the water supply as well as inspect all joints and also brand-new pipework for leaks as well as tighten them if needed. Load the bath tub and also inspect the overflow electrical outlet and also the regular outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the tub must wait till the bath tub has actually been used at least once as this will certainly resolve it right into its last placement.
Planning for the Setup
First of all, the sustaining framework supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop pressure on the bath tub.
Fit the versatile faucet ports to the bottom of the two taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to split a rigid seal, creating the water to penetrate the wall surface between the bathroom as well as the tiling, causing complications with wetness as well as feasible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and can sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always load the bathtub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can split fairly very early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily readily available on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that review about A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the web. Sharing is nice. Helping people is fun. Thanks for taking the time to read it.
Call Us Today Report this page